You are not logged in.

Unanswered posts



Important! This site has been replaced. All content here is read-only. Please visit our brand-new community at https://community.talend.com/. We look forward to hearing from you there!



#1 2016-09-04 13:24:08

rammohanatirajyam
Member
25 posts

rammohanatirajyam said:

[resolved] On component Ok Trigger from tJMSOutput

Tags: [development]

I have exposed Talend web service to other system and getting xmls requests and pushing to a MQ using tJMSOutput (which is perfectly working fine). I am trying to have two trigger flows after the  JMSOutput component i.e. On component Ok and on Component error, where I can provide the response to the web service request. Success response if the xml pushed properly into the MA, else error response if the xmls failed during the PUSH in MQ. I am not able to use the trigger i.e.  On component Ok and on Component error after JMSOutput. Could you please advise.

Offline

#2 2016-09-05 04:34:54

xdshi
Talend Team


xdshi said:

Re: [resolved] On component Ok Trigger from tJMSOutput

Hi,
What's the next component you are using?
Try to use "OnComponentOk" and "OncomponentError" between tJMSOutput and input or standalone component .
Please take a look at my screenshot.
Best regards
Sabrina
mini_1.png_20160904-2034.png


What we can do is to make sure that Talend will be your best choice!

Offline

#3 2016-09-05 09:15:54

rammohanatirajyam
Member
25 posts

rammohanatirajyam said:

Re: [resolved] On component Ok Trigger from tJMSOutput

Hi Sabrina, Thanks for the response.   I am using tESBProviderResponse / tESBProviderFault and the flow are like this. "OnComponentOk" --> tESBProviderResponse and "OnComponentError" --> tESBProviderFault . I am trying to use trigger flows after tJMSOutput but not able to connect to other components. 

mini_blob_20160905-0113.png

Last edited by rammohanatirajyam (2016-09-05 09:18:37)

Offline

#4 2016-09-05 11:31:57

xdshi
Talend Team


xdshi said:

Re: [resolved] On component Ok Trigger from tJMSOutput

Hi,
Talend don't allow to set up a "Circle" in work flow. You need to re-design your job.
Here is a KB article about:TalendHelpCenter:Can I create a Job with multiple paths from a single source to the same target?
Best regards
Sabrina


What we can do is to make sure that Talend will be your best choice!

Offline

#5 2016-09-05 16:45:20

rammohanatirajyam
Member
25 posts

rammohanatirajyam said:

Re: [resolved] On component Ok Trigger from tJMSOutput

Thank you ...  know that we can use tReplicate to create multiple flow. However I found other way to do it.. Thank You So much (Y)

Last edited by rammohanatirajyam (2016-09-05 17:37:06)

Offline

#6 2016-09-08 09:57:32

xdshi
Talend Team


xdshi said:

Re: [resolved] On component Ok Trigger from tJMSOutput

Hi,
Can we consider this topic as resolved?
Best regards
Sabrina


What we can do is to make sure that Talend will be your best choice!

Offline

#7 2016-09-08 20:32:11

rammohanavvs
Guest

rammohanavvs said:

Re: [resolved] On component Ok Trigger from tJMSOutput

AYes please.

Board footer

Talend Contributor Agreement - Talend Website Privacy Policy